Toyota Camry Wiper Blades Size Find Yours in 2 Minutes

Finding the right Toyota Camry wiper blade size should take two minutes. Not twenty. The problem is the Camry has run through eight generations. Toyota reshaped the windscreen in nearly every one. So the 2021 Toyota Camry wiper blade size shares nothing with the 1998 Toyota Camry wiper blade size. So you get blades that chatter, skip, or hang off the glass.

This guide breaks it down generation by generation. Match your build year and move on. You will find the 2013 Toyota Camry wiper blades size and the 2018 Toyota Camry wiper blades size here. Older fittings are covered too, like the 2001 Toyota Camry wiper blade size and the 2002 Toyota Camry wiper blades size. Every length is listed in inches and millimeters. Connector type is listed as well. Length alone will not get a blade onto the arm.

Why Camry wiper sizes keep changing

Wiper length comes from the windscreen. Not the badge. Toyota widened the glass and changed its rake over the years. The sweep pattern changed with it.

The Camry grew from a compact sedan into a full mid-size car. The blades grew too. A 19-inch pair in the late eighties became a 26-inch driver blade today.

The passenger side is the odd one. It does not simply scale up. On the XV40 and XV50, it actually shrank to 18 inches. The driver blade got longer, so the two arms needed clearance at the top of the sweep. Then it went back to 20 inches on the XV70. That is why a 2013 fitment will not work on a 2021 car.

Toyota Camry wiper blade size 

Generation	Model years	Driver side	Passenger side	Arm connector
V20	1987–1991	19″ / 475 mm	19″ / 475 mm	Hook
XV10	1992–1996	20″ / 500 mm	18″ / 450 mm	Hook
XV20	1997–2001	21″ / 525 mm	19″ / 475 mm	Hook
XV30	2002–2006	24″ / 600 mm	20″ / 500 mm	Hook
XV40	2007–2011	26″ / 650 mm	18″ / 450 mm	Hook
XV50	2012–2017	26″ / 650 mm	18″ / 450 mm	Hook
XV70	2018–2024	26″ / 650 mm	20″ / 500 mm	Pinch tab
XV80	2025–present	26″ / 650 mm	20″ / 500 mm	Pinch tab

No Camry sedan has ever had a rear wiper. Only the old V20 and XV10 wagons did. Those used a short rear blade of 14 to 16 inches.

Reading the Table for your car

1987–1996 Camry

These are the easy ones. The V20 runs a matched pair. You cannot fit the wrong blade to the wrong side. Check the exact fitment on the V20 sedan wiper or the V20 wagon wiper.

The XV10 splits into 20 and 18 inches. Australian-built XV10 sedans are often listed at 550 mm and 500 mm instead. Measure first if your car was delivered outside North America. Fitment for both bodies is listed on the XV10 sedan and the XV10 wagon.

1997–2001 Camry (XV20)

One fitment covers the whole run. Twenty-one inches and 19 inches. So the 1998 Toyota Camry wiper blade size and the 2001 Toyota Camry wiper blade size are identical. The 2000 facelift did not touch the wiper hardware.

2002–2006 Camry (XV30)

This is the biggest jump in Camry history. The driver blade went to 24 inches. Some catalogues list the passenger blade as 19 inches instead of 20. Both fit. The 20-inch just covers a little more glass. Australian XV30 models are commonly listed at 550 mm and 500 mm, as shown on the XV30 sedan fitment.

2007–2017 Camry (XV40 and XV50)

Eleven model years share one fitment. Twenty-six inches and 18 inches. That covers the 2013 Toyota Camry wiper blades size and every year around it. Hybrids use the same blades as petrol models. The XV50 sedan confirms 650 mm and 450 mm for this run.

2018 onward (XV70 and XV80)

The passenger blade returns to 20 inches. The arm changes to a pinch tab. That connector change matters more than the length. A hook blade from a 2017 Camry will not clip onto a 2018 arm. Right size, wrong fitting.

Check the connector, not just the length

Most fitment mistakes are connector mistakes.

Camry’s built up to 2017 use a hook arm. It is a J-shaped end. The blade slides in and locks against it. From 2018, Toyota moved to a pinch tab. The blade sits over a flat arm tip. Two small side tabs squeeze to release it.

Universal blades ship with adapters for both. Vehicle-specific blades usually arrive with the right fitting attached. If you buy a beam blade, check whether the adapter is pre-installed. The two styles do not swap once fitted.

Measuring your own blades

Take the old blade off. Lay it flat. Measure the full length, tip to tip. Not just the wiping edge. Round to the nearest inch. Land between two sizes? Go down, not up. A blade that runs long can clash with the opposite arm or overhang the A-pillar. Measure each side separately. On every Camry from 1992 onward the two blades differ. Swapping them is a common mistake.

When to replace them

Six to twelve months suits most drivers. Heat and UV wear the rubber faster than rain does. Cars parked outside in hot climates sit at the shorter end.

Replace them early if you notice any of this:

A smearing blade is not just annoying. On a wet motorway at night it costs you stopping distance. From 2018 onward, Camrys can blur the forward camera behind the windscreen too.

Conclusion

The Camry keeps things tidy. Eight generations, eight fitments, and long stretches where nothing changes. Built between 2007 and 2017? You need 26 and 18 inches. Built 2018 or later? Twenty-six and 20 inches with a pinch tab. Built 1997 to 2001? Twenty-one and 19 inches.

Match your generation from the table. Confirm the connector on the arm. The job takes a minute per side with no tools. One last thing. Always verify against your own car, not the year alone. Regional variants, wagon bodies, and locally built models sometimes carry different fitments.